Quck answer
To remove Schlage lock lever handles, follow these steps:
1. Locate the small hole on the lever handle. It is usually on the underside or the edge of the handle.
2. Insert a small Allen wrench or a paperclip into the hole and push it in until you feel resistance.
3. Apply firm pressure and continue pushing until the lever handle starts to loosen.
4. Once the handle is loose, pull it straight off the door.
5. Repeat the process for the other side of the door if necessary.
By following these steps, you will be able to easily remove Schlage lock lever handles.
Schlage lock lever handles are uniquely designed with a slight curve in the middle that resembles a smile or a frown when inverted. When installed correctly, the curve in the center of each handle should face upwards, creating a frown. In case you have a lock installed on a right-hand door, and you need to change it to a left-hand door, you will have to exchange the handle on the outside of the door with the one on the inside, and vice versa. To do this, you will need the pin tool that came with the lockset or a 6d finish nail, as well as the key.
Procedure for Removal
Replacing the Handles
Once both handles have been removed, drop the key cylinder into the handle that goes on the outside of the door and insert the key. Align the hole on the barrel of the handle with the tab on the lock mechanism, which is still attached to the door, then slide the barrel onto the lock. Turn the key to the reset position and push the barrel until it snaps in place. Turn the key 90 degrees and remove it.
When replacing the handle on the inside of the door, use the same procedure, except you do not need to insert the key. The barrel should snap into place.
Step 1
Insert the key into the handle on the outside of the door. Turn the key 90 degrees until it is vertically oriented in the reset position.
Step 2
Insert the pin tool or 6d finish nail into the hole at the other end of the handle barrel and push it in.
Step 3
Pull the handle off. Remove the key from the lock and take out the key cylinder from the handle barrel.
Step 4
Remove the handle from inside the door by inserting the removal tool or finish nail into the hole in the handle barrel and pushing it while pulling off the handle.
FAQ
1. How do I remove the Schlage lock lever handles?
To remove Schlage lock lever handles, start by locating the set screw on the underside of the handle. Use an Allen wrench or screwdriver to loosen and remove the set screw. Once the set screw is removed, the handle should easily slide off the spindle. If the handle is stuck, you can use a hammer and a block of wood to gently tap it off. Repeat this process for each lever handle that you want to remove.
2. Can I remove Schlage lock lever handles without any tools?
No, you will need a tool such as an Allen wrench or a screwdriver to remove the set screw that holds the lever handle in place. It is not recommended to try and remove the handles without the proper tools, as this may cause damage to the lock or the handle itself.
3. Are there any precautions I should take before removing Schlage lock lever handles?
Before removing Schlage lock lever handles, it is important to ensure that the door is unlocked and that you have a clear workspace. Additionally, it is recommended to wear protective gloves to prevent any injuries while handling the tools or the handles.
4. Can I reuse the same lever handles after removing them?
Yes, you can reuse the same lever handles after removing them from a Schlage lock. As long as the handles are in good condition and not damaged, you can reinstall them on another door or use them as replacements if needed.
5. How do I reinstall Schlage lock lever handles?
To reinstall Schlage lock lever handles, start by aligning the handle with the spindle and sliding it onto the spindle until it fits snugly. Then, tighten the set screw using an Allen wrench or a screwdriver. Make sure the handle is securely attached and does not wobble. Repeat this process for each lever handle that you want to reinstall.
6. Can I remove the Schlage lock lever handles without removing the entire lock?
Yes, you can remove the Schlage lock lever handles without removing the entire lock. The lever handles are typically separate from the lock mechanism and can be easily removed by following the steps mentioned earlier. This allows you to change or replace the handles without affecting the functioning of the lock.
7. Are there any specific maintenance tips for Schlage lock lever handles?
To keep Schlage lock lever handles in good condition, it is recommended to clean them regularly with a mild soap and water solution. Avoid using abrasive cleaners or solvents as they may damage the finish. Additionally, lubricate the moving parts of the handles with a silicone-based lubricant to ensure smooth operation.