Quck answer
To adjust the handle on a Moen Annabelle kitchen faucet, follow these steps:
1. Turn off the water supply to the faucet by closing the shut-off valves under the sink.
2. Remove the decorative cap on top of the handle by gently prying it off with a flathead screwdriver.
3. Use an Allen wrench to loosen the set screw located underneath the cap. Turn it counterclockwise to loosen and remove the handle.
4. Once the handle is off, locate the adjusting ring on the valve cartridge assembly. This ring controls the handle’s position.
5. Rotate the adjusting ring clockwise to tighten the handle’s position or counterclockwise to loosen it.
6. Reinstall the handle, tighten the set screw, and put the decorative cap back in place.
7. Turn on the water supply and test the handle to ensure it’s adjusted to your liking.
The Moen Annabelle is a kitchen faucet that comes with the Reflex system for easy operation and docking of the spout. This faucet is available at Home Depot, Lowe’s, and other stores that stock Moen products. It is a trendy faucet that can be mounted on a one-, two-, three-, or four-hole sink or countertop.
The single handle of the Moen Annabelle is attached to the right side of the faucet base. One of the most common problems with the Moen Annabelle is that there seems to be no way to remove the handle. However, the set screw is well hidden behind a cap under the lever. You have to remove the handle to service the valve or to tighten the handle if it’s loose. So, you need to know how to access this screw. Fortunately, it is not as challenging as it looks.
You Will Need a 3/32-Inch Hex Wrench
If you’re servicing a Moen faucet, put away your standard 1/8-inch hex wrench. The company uses hex screws that require a 3/32-inch wrench. You may have to purchase one from the store as it is not always included in the retractable set of hex keys. Keep it in a safe place because you’ll need it whenever you want to make an adjustment to your Moen kitchen faucet.
Accessing the Set Screw
To access the set screw, you need to pop off the cap. You can do this with your fingers or use a flat-head screwdriver to pry it off. It’s easier to remove the cap when the handle is all the way up, which turns the water on. So, close the shutoff valves under the sink to avoid wasting water.
Once the cap is off, insert the long end of the hex wrench into the hole. The wrench should be at a 30-degree angle with respect to the base of the faucet to engage the screw. If you insert the wrench by more than half its length, you missed the screw, and you have to start over. Turn the wrench counterclockwise to loosen the screw. You can’t lose the screw because it is seated inside the handle. When it’s loose enough, lift the handle and remove it. To replace the handle, reverse the procedure for removing it.
Moen Annabelle Cartridge Replacement
After removing the handle, you need to remove the dome to access the cartridge. Give it a half-turn in the counterclockwise direction or, on older models, completely unscrew it by hand. This reveals a plastic retaining nut that you can loosen with a wrench. Remove the nut and pull out the cartridge.
To replace an old cartridge, simply follow the reverse procedure. Use reasonable force to secure the retaining nut, being careful not to apply too much pressure as it is made of plastic and could break. Tighten the dome by hand to prevent any scratches caused by using a wrench or pliers. Remember to securely tighten the set screw for the handle with a hex wrench, or it will become loose and wobble.
FAQ
1. How do I adjust the handle on a Moen Annabelle kitchen faucet?
To adjust the handle on a Moen Annabelle kitchen faucet, start by locating the set screw on the handle. This screw is usually located on the back or underside of the handle. Use an Allen wrench to loosen the set screw by turning it counterclockwise. Once the set screw is loose, you can adjust the handle by rotating it clockwise or counterclockwise to the desired position. After making the adjustment, tighten the set screw by turning it clockwise with the Allen wrench. Test the handle to ensure it is secure and functioning properly.
2. What should I do if the handle on my Moen Annabelle kitchen faucet is loose?
If the handle on your Moen Annabelle kitchen faucet is loose, it is likely due to a loose set screw. To fix this issue, locate the set screw on the back or underside of the handle. Use an Allen wrench to tighten the set screw by turning it clockwise. This will secure the handle in place and prevent it from being loose. After tightening the set screw, test the handle to ensure it is no longer loose and is functioning properly.
3. Can I adjust the handle position on a Moen Annabelle kitchen faucet?
Yes, you can adjust the handle position on a Moen Annabelle kitchen faucet. To do this, locate the set screw on the back or underside of the handle. Loosen the set screw using an Allen wrench by turning it counterclockwise. Once the set screw is loose, you can adjust the handle position by rotating it clockwise or counterclockwise to the desired position. After making the adjustment, tighten the set screw by turning it clockwise with the Allen wrench. This will secure the handle in the new position. Test the handle to ensure it is secure and functioning properly.