Quck answer
To install Kraftmaid crown molding, follow these steps:
1. Measure and mark the desired height for the crown molding on the wall.
2. Cut the crown molding to the appropriate length using a miter saw.
3. Apply adhesive or construction adhesive to the back of the crown molding.
4. Press the molding firmly against the wall, aligning it with the marked height.
5. Use finishing nails or a nail gun to secure the molding to the wall.
6. Fill any nail holes or gaps with wood filler and sand it smooth.
7. Paint or stain the crown molding to match your desired finish.
8. Enjoy the elegant and finished look that Kraftmaid crown molding adds to your space.
Remember to follow the manufacturer’s instructions and take proper safety precautions when working with power tools.
Kraftmaid crown molding is designed to be installed on top of kitchen cabinetry and can provide a custom look. The installation process is easy and should take approximately one to two hours, depending on the kitchen’s size. Kraftmaid crown molding comes prefinished and ready to install on cabinets. Once installed, any holes can be filled using tinted wood filler that matches the molding’s paint or stain.
Step 1
Measure the top of the cabinets using a measuring tape. Have someone hold one side of the tape while you take measurements from the other side. Record the measurements on a piece of paper.
Step 2
Transfer the measurements from the top of the kitchen cabinets to a 1-by-2-inch board using a pencil.
Step 3
Place the 1-by-2-inch board on a miter saw and cut it to size at a 90-degree angle. Use the cut pieces to create a frame for the top of the cabinet. Nail the pieces to size with a finish nail gun. The finished frame should sit on the top of the cabinet.
Step 4
Mark the measurements from the top of the kitchen cabinets on a piece of Kraftmaid crown molding with a pencil.
Step 5
Set the Kraftmaid molding on the miter saw with the top of the molding resting against the saw table and the bottom of the molding resting against the saw fence. Set the saw to a 45-degree angle and cut the molding to size. For corners, cut the molding on either side of the corner to an opposite 45-degree angle.
Step 6
Hold the Kraftmaid crown molding in place on the 1-by-2-inch frame. Nail the molding in place with a finish nail gun.
FAQ
1. What tools do I need to install Kraftmaid crown molding?
To install Kraftmaid crown molding, you will need a few basic tools including a miter saw, a coping saw, a tape measure, a pencil, a level, a nail gun or hammer, a putty knife, and some caulk. It is also helpful to have a stud finder and a ladder or step stool for reaching high areas.
2. Where should I start when installing Kraftmaid crown molding?
When installing Kraftmaid crown molding, it is best to start in a corner of the room and work your way around. Begin by measuring and marking the wall where the first piece of molding will be installed. Then, cut the molding to the appropriate length and angle using a miter saw. Attach the molding to the wall using a nail gun or hammer, making sure to hit the studs for a secure hold.
3. How do I cope the ends of Kraftmaid crown molding?
To cope the ends of Kraftmaid crown molding, start by cutting a 45-degree angle on one end using a miter saw. Then, use a coping saw to remove the excess wood along the profile of the molding. This will allow the molding to fit tightly against the adjacent piece. Sand down any rough edges and test the fit before attaching the coped end to the wall.
4. How do I handle inside and outside corners when installing Kraftmaid crown molding?
Inside corners can be mitered by cutting each piece of molding at a 45-degree angle in the opposite direction. For outside corners, cut each piece of molding at a 45-degree angle in the same direction. If the corners are not perfectly square, you may need to adjust the angles slightly for a tight fit. Use a level to ensure the molding is straight and plumb before securing it to the wall.
5. What is the best way to fill nail holes in Kraftmaid crown molding?
The best way to fill nail holes in Kraftmaid crown molding is to use a putty knife and some wood filler or caulk. Simply scoop a small amount of filler onto the putty knife and press it into the hole, smoothing it out as you go. Allow the filler to dry completely, then sand it down until it is flush with the surface of the molding. If needed, touch up the paint or stain to match the surrounding area.
6. Can I install Kraftmaid crown molding myself, or should I hire a professional?
Installing Kraftmaid crown molding can be a DIY project, but it does require some skill and attention to detail. If you have experience with carpentry and feel confident in your abilities, you can definitely tackle this project on your own. However, if you are unsure or lack the necessary tools, it may be best to hire a professional to ensure the job is done correctly.
7. Are there any tips or tricks for installing Kraftmaid crown molding?
One helpful tip for installing Kraftmaid crown molding is to cut each piece slightly longer than necessary and then trim it down for a perfect fit. This allows for any discrepancies in measurements or angles. Additionally, make sure to properly caulk and seal any gaps or joints to create a seamless and professional-looking finish. Take your time, measure twice, and double-check your angles to ensure a successful installation.